Seat Belts › Front › Buckle Assembly Vehicle Recalls

Chrysler (FCA US, LLC) is recalling certain 2022-2023 Ram Promaster vehicles. The driver seat belt warning light and audible chime may not activate as intended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."

Honda (American Honda Motor Co.) is recalling certain 2017-2020 CR-V, 2018-2019 Accord and Accord Hybrid, 2018-2020 Odyssey, 2019 Insight, and 2019-2020 Acura RDX vehicles. A manufacturing issue with the front seat belts may cause the seat belt buckle channel to interfere with the release button, preventing the seat belt buckle from latching.

BMW of North America, LLC (BMW) is recalling certain 2021 330i, 330i xDrive, M340i, M3, and 330e xDrive vehicles. The bolt securing the seat belt assembly to the frame was not tightened to specification.

BMW of North America, LLC (BMW) is recalling certain 2020 X3 xDrive30e, X4 xDrive30i, X4 M40i, X4M, 330i, 330i xDrive, M340i, 840i Gran Coupe, 840i xDrive Gran Coupe, M850i xDrive Gran Coupe, M8 Gran Coupe, X3 sDrive30i, X3 xDrive30i, X3 M40i, X3M, and 840i xDrive Convertible vehicles. The sensors in the front seat belt buckles may inaccurately detect a belted occupant as unbelted, possibly causing the air bag and seat belt pretensioners to deploy improperly in the event of a crash.

Volvo Car USA LLC (Volvo) is recalling certain model year 2016-2017 XC90, S90, XC60, V60 Cross Country, V60, S60 Cross Country, S60, and S60 Inscription vehicles manufactured February 16, 2015, to August 22, 2016. On the affected vehicles, the front passenger seat belt buckle attaching stud may loosen, allowing the buckle to separate from the seat belt bracket. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 210, "Seat Belt Assembly Anchorages" and number 209, "Seat Belt Assemblies."

Nissan North America, Inc. (Nissan) is recalling certain model year 2015 Nissan Armada vehicles manufactured April 30, 2015, to June 5, 2015. The affected vehicles may have been built with driver or front passenger seat belt assemblies that may not properly latch or that may not unlatch when the release button is pressed. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection" and number 209, " Seat Belt Assemblies."

Kia Motors America (Kia) is recalling certain model year 2016 Kia Sorento vehicles manufactured October 23, 2014, to December 10, 2014. The affected vehicles have a front passenger seat belt whose buckle latch assembly may prevent the front passenger from fastening the seat belt.

Hyundai Motor America (Hyundai) is recalling certain model year 2015 Sonata vehicles manufactured April 25, 2014, to December 4, 2014. The affected vehicles have a front passenger seat belt whose buckle latch assembly may prevent the front passenger from fastening the seat belt.

GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2011 CADILLAC SRX, CHEVROLET EQUINOX AND GMC TERRAIN VEHICLES. THE DRIVER AND /OR FRONT PASSENGER SAFETY BELT BUCKLE ANCHOR MAY FRACTURE AND SEPARATE NEAR THE SEAT ATTACHMENT IN A VEHICLE CRASH.

VOLKSWAGEN IS RECALLING APPROXIMATELY 5,000 MY 2009 CC VEHICLES. SOME AFFECTED VEHICLES MAY HAVE AN INCORRECTLY ROUTED RIGHT FRONT PASSENGER SEAT BELT BUCKLE WIRING HARNESS, CREATING THE POTENTIAL FOR WIRES TO BECOME DAMAGED WHEN THE SEAT IS MOVED FULLY UP OR DOWN OR BACK AND FORTH. IF THIS WIRING DAMAGE OCCURS, THE AIRBAG CONTROL MODULE WILL SWITCH TO A FALLBACK ALGORITHM AND DEACTIVATE THE PASSENGER'S FRONTAL AIR BAG.

CERTAIN VEHICLES LOCATED IN GUAM AND SAIPAN WERE BUILT WITH A SEAT BELT BUCKLE WITH AN IMPROPER ULTRASONIC WELD OF THE SPRING RIB AND FIXATION RIB OF BUCKLE UNDERCOVER IN BOTH FRONT SEAT BELTS. A SPRING RIB OR FIXATION RIB COULD BREAK AND REMAIN INSIDE THE BUCKLE, AND THE SEAT BELT TONGUE MAY NOT BE INSERTED INTO THE BUCKLE, OR THE PUSH BUTTON MAY BECOME STUCK, RESULTING IN AN OCCUPANT NOT BEING ABLE TO UNLATCH THE BUCKLE.

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A FRONT PASSENGER POWER SEAT, WHEN INSTALLING CERTAIN REAR-FACING INFANT CHILD SEAT BASES ONTO THE SEAT WITH AN EXCESSIVELY HIGH SEATBELT TENSION, IT MAY BE POSSIBLE TO UNSEAT A COMPONENT CALLED THE BUCKLE STATUS SWITCH FROM THE SEAT BELT BUCKLE.

ON CERTAIN PASSENGER AND SPORT UTILITY VEHICLES, THE FRONT SAFETY BELT BUCKLES MAY EMIT A "CLICK" SOUND DURING THE BUCKLING PROCESS THAT IS SIMILAR TO THE SOUND EMITTED WHEN A BUCKLE IS BEING LATCHED, WHEN IT IS NOT.

CERTAIN VANS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES." THESE VEHICLES MAY HAVE BEEN PRODUCED WITH SEAT BELT BUCKLE ASSEMBLIES CONTAINING A LATCH WITH A BRITTLE CONDITION THAT MAY NOT WITHSTAND THE FORCE REQUIREMENTS OF THE STANDARD.

ON CERTAIN SPORT UTILITY VEHICLES, A POST WITHIN THE SAFETY BELT BUCKLE COVERS COULD FRACTURE, WHICH COULD AFFECT LATCH FUNCTION, RESULTING IN EITHER A "NO LATCH" OR "PARTIAL LATCH" CONDITION. IN THE "PARTIAL LATCH" CONDITION, THE BUCKLE TONGUE CAN BE INSERTED INTO THE BUCKLE AND APPEAR TO BE ENGAGED, BUT WILL RELEASE FROM THE BUCKLE WITHOUT THE PUSH BUTTON BEING DEPRESSED WHEN A RELATIVELY LOW LOAD IS APPLIED, SUCH AS WHEN AN OCCUPANT MOVES SLIGHTLY IN THE SEAT.

ON CERTAIN SPORT UTILITY VEHICLES, A POST WITHIN THE SAFETY BELT BUCKLE COVERS COULD FRACTURE, WHICH COULD AFFECT LATCH FUNCTION, RESULTING IN EITHER A "NO LATCH" OR "PARTIAL LATCH" CONDITION. IN THE "PARTIAL LATCH" CONDITION, THE BUCKLE TONGUE CAN BE INSERTED INTO THE BUCKLE AND APPEAR TO BE ENGAGED, BUT WILL RELEASE FROM THE BUCKLE WITHOUT THE PUSH BUTTON BEING DEPRESSED WHEN A RELATIVELY LOW LOAD IS APPLIED, SUCH AS WHEN AN OCCUPANT MOVES SLIGHTLY IN THE SEAT.

ON CERTAIN SPORT UTILITY VEHICLES, THE DRIVER SEAT BELT BUCKLE WIRING COULD BE DAMAGED BY INTERFERENCE WITH THE DRIVER SEAT CUSHION HEIGHT ADJUSTER MECHANISM. DAMAGED DRIVER SEAT BELT BUCKLE WIRING COULD CAUSE THE SEAT BELT WARNING LAMP OR THE SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG WIRING LAMP TO ILLUMINATE. IT COULD ALSO CAUSE THE AIR BAG FUSE (CAVITY NUMBER 5) TO OPEN, PREVENTING AIR BAG DEPLOYMENT. DAMAGED DRIVER SEAT BELT BUCKLE WIRING COULD CAUSE THE SEAT BELT WARNING LAMP OR THE SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG WIRING LAMP TO ILLUMINATE. IT COULD ALSO CAUSE THE AIR BAG FUSE (CAVITY NUMBER 5) TO OPEN, PREVENTING AIR BAG DEPLOYMENT.

CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES." THE LEFT AND RIGHT FRONT SEAT BELT BUCKLE/LATCH ASSEMBLIES WERE IMPROPERLY MANUFACTURED.

ON CERTAIN VANS WITH A GROSS VEHICLE WEIGHT OF LESS THAN 8,500 POUNDS, DURING A VEHICLE CRASH SUFFICIENT ENOUGH TO DEPLOY THE SAFETY BELT PRETENSIONER, THE FRONT SAFETY BELT BUCKLES MAY NOT RELEASE AFTER THE VEHICLE CRASH, OR ALTERNATELY MAY EJECT THE SAFETY BELT LATCH DURING THE VEHICLE CRASH.

ON CERTAIN PASSENGER VEHICLES, THE CONNECTION OF THE SAFETY BELT BUCKLE TO THE STEEL ROPE OF THE TENSIONER DOES NOT MEET BMW SPECIFICATIONS. IN SEVERE FRONTAL CRASHES, THIS CONNECTION CAN DETACH.

ON CERTAIN PASSENGER VEHICLES, THE DRIVER SEAT BELT BUCKLE WIRING COULD BE DAMAGED BY INTERFERENCE WITH THE DRIVER SEAT CUSHION HEIGHT ADJUSTER MECHANISM.

CERTAIN SEDANS AND COUPES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES." CERTAIN REAR SEAT BELT BUCKLES WERE IMPROPERLY MANUFACTURED.

VEHICLE DESCRIPTION: CERTAIN SEDANS AND COUPES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES." CERTAIN REAR SEAT BELT BUCKLES WERE IMPROPERLY MANUFACTURED.

VEHICLE DESCRIPTION: THE FOLLOWING VEHICLES WERE REPAIRED WITH INCORRECT PARTS: 2002 ACURA 3.2TL SEDANS WITH REPLACEMENT BUCKLES INSTALLED PER RECALL 01V-166001; CERTAIN 2000 ACURA 3.2TL VEHICLES WITH REPLACEMENT BUCKLES INSTALLED AS PRODUCT UPDATE REPAIRS; AND CERTAIN 2000-2002 ACURA 3.2TL VEHICLES WITH REPLACEMENT BUCKLES INSTALLED AS WARRANTY OR COLLISION REPAIRS. REPAIRS WERE MADE FROM MARCH 9 THROUGH JULY 27, 2001. SOME OF THE NONCOMPLIANT BUCKLES WERE MISLABELED AND REDISTRIBUTED TO ACURA DEALERS TO BE USED AS RECALL REPAIR PARTS. HONDA ALSO DETERMINED THAT INCORRECT FRONT SEAT BELT BUCKLE REPLACEMENT PARTS WERE USED FOR SOME PRODUCT UPDATE REPAIRS OF 2000 ACURA 3.2TL VEHICLES, AND WARRANTY OR COLLISION REPAIRS OF 2000-2002 3.2TL VEHICLES. THESE SEAT BELT BUCKLES MAY NOT COMPLY WITH REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES."

VEHICLE DESCRIPTION: PASSENGER AND SPORT UTILITY VEHICLES, PICKUP TRUCKS, AND MINIVANS. EQUIPPED WITH SEAT BELTS SUPPLIED BY TRW. IT IS POSSIBLE THAT THE DRIVER'S AND/OR FRONT PASSENGER'S OUTBOARD SEAT BELT BUCKLE MAY NOT FULLY LATCH. FORD CROWN VICTORIA BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01 MERCURY GRAND MARQUIS BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01. LINCOLN TOWN CARS BUILT AT WIXOM ASSEMBLY PLANT FROM 3/27/00 - 5/30/01. LINCOLN NAVIGATORS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 - 5/31/01. FORD WINDSTARS BUILT AT OAKVILLE ASSEMBLY PLANT FROM 3/23/00 - 5/30/01. FORD RANGERS BUILT AT TWIN CITIES PLANT FROM 3/28/00 - 5/30/01, AND ALSO AT THE EDISON PLANT FROM 3/13/00 - 5/25/01. FORD F-150 TRUCK BUILT AT NORFOLK PLANT FROM 4/18/00 - 5/25/00; AT ONTARIO PLANT FROM 5/10/00 - 5/28/01; AT KANSAS CITY PLANT FROM 9/11/99 - 5/25/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/9/01. FORD SUPER DUTY F-250, F-350, F-450, AND F-550 TRUCKS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 5/27/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/19/01. FORD EXCURSIONS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 10/2/00. FORD EXPEDITIONS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 - 5/31/01.

VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." CERTAIN DRIVER AND PASSENGER SEAT BELT BUCKLES WERE IMPROPERLY MANUFACTURED.

VEHICLE DESCRIPTION: PASSENGER CARS. THE SEAT BELT BUCKLE TONGUE MAY NOT FULLY EJECT FROM THE BUCKLE ASSEMBLY WHEN THE RELEASE BUTTON IS PUSHED SLOWLY. THIS CONDITION COULD ALSO RESULT IN A PARTIAL LATCH OF THE TONGUE IN THE BUCKLE.

VEHICLE DESCRIPTION: PASSENGER VEHICLES, HEARSE, AND LIMOUSINES. SOME OF THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THESE VEHICLES HAVE SEAT BELTS THAT MAY NOT MEET THE 30-POUND PUSH BUTTON RELEASE EFFORT REQUIREMENT OF THE STANDARD.

VEHICLE DESCRIPTION: MINI VANS. THESE VEHICLES MAY HAVE THE PLASTIC TRIM COVER AROUND THE BASE OF THE FRONT SEAT SAFETY BELT BUCKLE TRAPPED BETWEEN THE SHOULDER OF THE RESTRAINT ANCHORAGE BOLT AND THE SEAT PEDESTAL. THIS COULD EVENTUALLY ALLOW THE SEAT BELT BUCKLE BOLT TO LOOSEN.