Engine And Engine Cooling Vehicle Recalls

Jaguar Land Rover North America, LLC (Land Rover) is recalling certain 2024 Land Rover Range Rover vehicles. The engine mounted oil cooler hoses may not be secured properly, which can result in oil leaking onto the road.

Subaru of America, Inc. (Subaru) is recalling certain 2024 Forester vehicles. The engine water pipe may have loose attachment bolts, allowing the pipe to lose its seal and leak coolant.

Chrysler (FCA US, LLC) is recalling certain 2014-2019 Ram 1500 and 2014-2020 Jeep Grand Cherokee vehicles equipped with 3.0L Diesel engines. The crankshaft position sensor tone wheel may delaminate, causing the engine to lose its ability to synchronize the fuel injector pulses and cam shaft timing, possibly resulting in an engine stall.

Ford Motor Company (Ford) is recalling certain 2020-2022 Escape, 2021-2022 Lincoln Corsair, and 2022 Maverick vehicles equipped with 2.5L HEV or PHEV engines. In the event of an engine failure, engine oil and fuel vapor may be released into the engine compartment and accumulate near ignition sources such as hot engine or exhaust components, possibly resulting in an engine compartment fire.

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2020 Toyota Avalon Hybrid, Camry, Camry Hybrid and Lexus ES300h and 2019-2020 RAV4 and RAV4 Hybrid vehicles equipped with 2.5L 4-Cylinder engines. Porosity in the engine castings may result in cracks than can allow coolant to leak internally and/or externally.

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain model year 2013 Audi Q7 vehicles manufactured June 5, 2012, to November 29, 2012 and equipped with a 3.0L TDI engine. In the affected vehicles, a check valve in the engine may become contaminated with plastic debris and allow engine oil to leak into the brake booster.

Jaguar Land Rover North America, LLC (Jaguar) is recalling certain model year 2013 and 2014 XF 2.0L GTDi vehicles manufactured May 2013 through October 2013. The hose clamp for the Charge Air Cooler (CAC) hose may be out of position and loose, allowing the hose to detach.

Honda is recalling certain model year 2013 CB500 (FA, F, XA, X) and CBR500 (RA, R) motorcycles. The rocker arm shaft retaining bolts may have been manufactured incorrectly resulting in the bolts loosening during engine operation. A loose bolt will initially result in a slow leak of engine oil, but if not addressed, the bolt can come out of the cylinder head entirely.

Jaguar Land Rover North America, LLC (Jaguar) is recalling certain model year 2013 XF 2.0L GTDi vehicles manufactured July 2012 through May 2013. The hose clamp for the Charge Air Cooler (CAC) hose may be out of position and loose, allowing the hose to detach.

Chrysler Group LLC (Chrysler) is recalling certain model year 2013 RAM 1500 trucks manufactured manufactured June 25, 2012, through December 12, 2012. In the affected vehicles, the coolant bypass valve may stick in a position that does not allow coolant to flow into the heater core. Thus, these vehicles fail to conform to the requirements of Federal Vehicle Motor Safety Standard (FMVSS) No. 103, "Windshield Defrosting and Defogging Systems."

Chrysler Group LLC (Chrysler) is recalling certain model year 2013 Dodge Ram 2500 and 3500 trucks manufactured January 7, 2013, through March 6, 2013. The engine cover may trap an excessive amount of heat under the cover.

Honda is recalling certain model year 2004-2008 Acura TSX vehicles originally sold in, or currently registered in, Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. In states that use corrosive materials for deicing, driver's footwear may bring in materials that saturate the vehicle's carpeting, which is in contact with the vehicle's engine Electronic Control Unit (ECU). As a result, the ECU case may experience rust or corrosion. This damage may potentially cause the engine to stall.

This is an update to a recently announced recall. Ford is recalling certain model year 2013 Escape vehicles manufactured from October 5, 2011, through November 26, 2012, equipped with 1.6L engines, as well as certain model year 2013 Fusion vehicles manufactured from February 3, 2012, through November 29, 2012, equipped with 1.6L engines. Coolant system leaks may cause the engines to overheat and leak flammable engine fluids.

Toyota is recalling certain model year 2004-2009 Prius vehicles manufactured August 6, 2003, through March 30, 2009 and FCHV-adv vehicles manufactured December 12, 2008, through September 13, 2011. During manufacturing, a scratch may have occurred inside of the electrically driven water pump at the coil wire. The coil wire may corrode at the scratched portion.

Ford is recalling certain model year 2013 Escape vehicles manufactured from October 5, 2011, through August 31, 2012, equipped with 1.6L engines. The cylinder head cup plug (freeze plug) may become dislodged resulting in significant loss of engine coolant.

Mazda is recalling certain model year 2001 through 2006, and 2008, Tribute vehicles equipped with 3.0L V6 engines and speed control. Inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. This risk exists regardless of whether or not speed control (cruise control) is used.

Ford Motor Company is recalling certain model year 2001 through 2004 Escape vehicles equipped with 3.0L V6 engines and speed control manufactured from October 22, 1999, through January 23, 2004. Inadequate clearance between the engine cover and the speed control cable connector could result in a stuck throttle when the accelerator pedal is fully or almost-fully depressed. This risk exists regardless of whether or not speed control (cruise control) is used.

GENERAL MOTORS (GM) IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 CHEVROLET CRUZE VEHICLES MANUFACTURED FROM OCTOBER 2, 2009, THROUGH MAY 31, 2012. SPILLED OR DRIPPING OIL (SUCH AS AFTER AN OIL CHANGE) MAY COLLECT IN THE ENGINE SHIELD (BELLYPAN) NEAR HOT ENGINE OR EXHAUST SYSTEM SURFACES. AS A RESULT, THE OIL AND THE ENGINE SHIELD MAY IGNITE AND BURN.

NISSAN IS RECALLING CERTAIN MODEL YEAR 2011 INFINITI FX, MODEL YEAR 2012 INFINITI M, MODEL YEAR 2011-2012 NISSAN FRONTIER, MODEL YEAR 2011-2012 NISSAN XTERRA, MODEL YEAR 2011-2012 NISSAN PATHFINDER, AND MODEL YEAR 2012 NISSAN NV VEHICLES. SOME OF THE BOLTS THAT CONNECT THE ENGINE OIL COOLER AND THE ENGINE OIL FILTER TO THE ENGINE IN THESE VEHICLES MAY HAVE BEEN MANUFACTURED TO BELOW SPECIFICATION STRENGTH. AS A RESULT, THE BOLT MAY BREAK AT THE OIL FILTER ATTACHMENT POINT AND CAN CAUSE AN ENGINE OIL LEAK.

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2004 AVALON VEHICLES; 2004 AND 2005 CAMRY, CAMRY SOLARA, HIGHLANDER, AND SIENNA VEHICLES, 2006 HIGHLANDER HYBRID; 2004 AND 2005 LEXUS ES330 AND RX330; AND 2006 LEXUS RX400H VEHICLES MANUFACTURED FROM JUNE 1, 2004 THROUGH MARCH 31, 2005, EQUIPPED WITH THE 1MZ-FE OR 3MZ-FE ENGINE. THE AMOUNT OF ADHESIVE AGENT APPLIED BETWEEN THE OUTER RING AND THE TORSIONAL RUBBER DAMPER (INNER RING) IN THE CRANKSHAFT PULLEY MAY BE INADEQUATE. IF THE ADHESIVE IS INSUFFICIENT, THERE IS A POSSIBILITY THAT THE OUTER RING MAY BECOME MISALIGNED AND IT MAY NOT PROPERLY ROTATE WITH THE INNER RING, CAUSING NOISE AND/OR ILLUMINATION OF THE BATTERY DISCHARGE INDICATOR LIGHT.

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2012 CHRYSLER VEHICLES, INCLUDING 200 AND TOWN AND COUNTRY MODELS, DODGE VEHICLES, INCLUDING CHARGER, DURANGO, GRAND CARAVAN AND JOURNEY MODELS AND JEEP GRAND CHEROKEE VEHICLES MANUFACTURED FROM AUGUST 31, 2011, THROUGH SEPTEMBER 13, 2011, THAT ARE EQUIPPED WITH 3.6L ENGINES. THESE ENGINES MAY EXPERIENCE CONNECTING ROD BEARING FAILURE DUE TO DEBRIS INSIDE THE ENGINE BLOCK.

HONDA IS RECALLING CERTAIN MODEL YEAR 2009-2010 HONDA FIT VEHICLES. THERE IS A POTENTIAL FOR ONE OR MORE OF THE FOUR SPRING ASSEMBLIES ON THE ENGINE'S VARIABLE VALVE TIMING AND LIFT ELECTRONIC CONTROL (VTEC) SYSTEM TO FAIL.

ISUZU IS RECALLING CERTAIN MODEL YEAR 2006-2007 ISUZU NPR, NQR, NRR, GMC W3500, W4500, W5500, AND CHEVROLET W3500, W4500, AND W5500 VEHICLES. THE OIL PIPE BOLTS WERE NOT TIGHTENED PROPERLY DURING THE VEHICLE PRODUCTION PROCESS. IF NOT ADEQUATELY TIGHTENED, THE BOLT MAY LOOSEN AFTER PROLONGED VEHICLE OPERATION, WHICH CAN RESULT IN OIL SEEPAGE OR LEAKAGE FROM THE PACKING SEALS. IN GENERAL, AS OIL IS LOST, THE OIL WARNING LAMP WILL ILLUMINATE, AND THERE MAY BE ABNORMAL ENGINE NOISE AND LOSS OF OIL CAN CAUSE ENGINE SEIZURE.

VOLVO IS RECALLING CERTAIN MODEL YEAR 2011, S80, S60, XC70 AND XC60 VEHICLES. THE SOFTWARE CALIBRATION FOR THE FUEL CUT-OFF FUNCTIONALITY IN THE ENGINE CONTROL MODULE (ECM) IS TOO SENSITIVE.

NISSAN IS RECALLING CERTAIN MODEL YEAR 2004-2006 ARMADA, TITAN, INFINITI QX56 AND MODEL YEAR 2005-2006 FRONTIER, PATHFINDER AND XTERRA VEHICLES. THE INTELLIGENT POWER DISTRIBUTION MODULE (IPDM) ASSEMBLY CONTAINS AN ENGINE CONTROL MODULE (ECM) RELAY THAT HAS A DIODE FOR ELECTRICAL CURRENT NOISE REDUCTION. THE ECM RELAY MAY ALLOW SILICON VAPOR TO FORM AND, OVER TIME, THE SILICON EVAPORATES FROM THE DIODE MOLDING WHICH CAUSES SILICON OXIDE TO DEVELOP ON THE ECM RELAY CONTACT DUE TO ARCING.

FORD IS RECALLING CERTAIN MODEL YEAR 2008-2009 F-650 AND F-750 TRUCKS EQUIPPED WITH CATERPILLAR C7 ENGINE. THE #5 AND #6 FUEL LINES MAY CRACK AT THE FASTENING POINT TO THE COMMON FUEL RAIL AND CAUSE A FUEL LEAK.

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2008 COROLLA AND COROLLA MATRIX VEHICLES. THE ENGINE CONTROL MODULE (ECM) FOR THE SUBJECT MODELS EQUIPPED WITH THE 1ZZ-FE ENGINE AND TWO-WHEEL DRIVE MAY HAVE BEEN IMPROPERLY MANUFACTURED. THERE IS A POSSIBILITY THAT A CRACK MAY DEVELOP AT CERTAIN SOLDER POINTS OR ON VARISTORS ON THE CIRCUIT BOARD.

JAGUAR IS RECALLING CERTAIN MODEL YEAR 2010-2011 JAGUAR XK AND MODEL YEAR 2010 XF V8 5.OL GASOLINE ENGINE VEHICLES. THE IN-TANK ELECTRIC FUEL PUMP MAY NOT BE CORRECTLY ACTIVATED AS THE FUEL PUMP RELAY IS NOT ENERGIZED FOLLOWING A VEHICLE START UP CYCLE. AN INADEQUATE SUPPLY OF FUEL TO THE ENGINE COULD RESULT.

GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2010 CADILLAC SRX EQUIPPED WITH A 2.8L V6 ENGINE. IF LOW OCTANE (REGULAR) FUEL IS USED IN THE VEHICLE INSTEAD OF THE REQUIRED HIGH OCTANE (PREMIUM) FUEL AS STATED IN THE OWNER MANUAL AND ON THE FUEL FILLER DOOR, THE COMBINATION OF REGULAR FUEL USAGE AND AGGRESSIVE DRIVING MANEUVERS MAY INDUCE PRE-IGNITION. IF PRE-IGNITION OCCURS, YOU MAY HEAR A PINGING OR KNOCKING SOUND FROM THE ENGINE.

BMW IS RECALLING CERTAIN MODEL YEAR 2008 THROUGH 2010 F650 GS AND F800 GS MOTORCYCLES MANUFACTURED BETWEEN JANUARY 2008 AND DECEMBER 2009. DURING ENGINE OPERATION, A VACUUM IS CREATED IN ORDER TO DRAW FRESH AIR INTO THE CANISTER. THIS AIR THEN MIXES WITH THE FUEL VAPORS CAPTURED BY THE CANISTER, AND IS SUBSEQUENTLY COMBUSTED. DUE TO THE ROUTING OF THE VENTILATION HOSE, WATER NEAR THE END OF THE HOSE COULD BE DRAWN INTO THE CHARCOAL CANISTER.

BMW IS RECALLING CERTAIN MODEL YEAR 2009 AND 2010 K1300 S AND K1300 GT MOTORCYCLES MANUFACTURED BETWEEN SEPTEMBER 11, 2008 AND NOVEMBER 19, 2009. POOR FUEL QUALITY MAY LEAD TO SMALL DEPOSITS WITHIN THE THROTTLE BODIES. DURING ENGINE OPERATION IN A LOW RPM RANGE, TYPICALLY NEAR IDLE SPEED (WHEN COMING TO A STOP) AIR FLOW COULD BE SUFFICIENTLY RESTRICTED AND ENGINE STALLING COULD OCCUR.

NISSAN IS RECALLING 362,891 MY 2003-2007 MURANO VEHICLES. THE INTAKE AIR DUCTS, WHICH ARE CONNECTED TO THE INTERMEDIATE RESONATOR IN THE AIR INTAKE SYSTEM OF THE ENGINE, MAY SEPARATE FROM THE RESONATOR WITH ENGINE MOVEMENT. THIS SEPARATION OCCURS DUE TO THE PREMATURE AGING OF THE MATERIAL USED IN THE INTAKE AIR DUCTS WHICH CAUSES EXCESSIVE SHRINKING.

GENERAL MOTORS IS RECALLING 1,497,516 MY 1997-2003 BUICK REGAL, MY 1998-2003 CHEVROLET LUMINA, MONTE CARLO AND IMPALA, MY 1998-1999 OLDSMOBILE INTRIGUE, MY 1997-2003 PONTIAC GRAND PRIX VEHICLES EQUIPPED WITH A 3.8L V6 NATURALLY ASPIRATED ENGINE. SOME OF THESE VEHICLES HAVE A CONDITION IN WHICH DROPS OF ENGINE OIL MAY BE DEPOSITED ON THE EXHAUST MANIFOLD THROUGH HARD BRAKING.

ROUSH IS RECALLING 213 MY 2007-2008 FORD F-150 TRUCKS ALTERED TO OPERATE USING LIQUID PROPANE INJECTION. THE HYDRO-CARBON PAPER AFFIXED TO THE INSIDE OF THE AIRBOX LID WITH ADHESIVE MAY BECOME DISLODGED DURING OPERATION.

VOLKSWAGEN IS RECALLING 4,079 MY 2008 PASSAT AND 2,500 MY 2009 TIGUAN PASSENGER VEHICLES EQUIPPED WITH 2.0T FSI ULEV II ENGINES. THESE VEHICLES HAVE AN ENGINE CONTROL MODULE (ECM) CONTAINING SOFTWARE THAT MAY NOT PROPERLY CONTROL ENGINE IDLE WITH THE AIR CONDITIONING TURNED ON. IN RARE CASES, THE ECM MAY UNEXPECTEDLY INCREASE ENGINE RPM.

GM IS RECALLING 207,542 MY 1997-2003 BUICK REGAL AND PONTIAC GRAND PRIX VEHICLES EQUIPPED WITH A 3.8L SUPERCHARGED V-6 ENGINE. THESE VEHICLES HAVE HIGHER FRONT ROCKER COVER GASKET TEMPERATURES, CREATING THE POTENTIAL FOR EARLIER DEGRADATION OF THE FRONT ROCKER COVER GASKET AND EVENTUAL OIL SEEPAGE.

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANKSHAFT POSITION SENSOR CAN OVERHEAT CAUSING A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.

ON CERTAIN PICKUP TRUCKS EQUIPPED WITH AN 8.1L V8 ENGINE, THE CRANKSHAFT POSITION CAN OPERATE INTERMITTENTLY OR FAIL COMPLETELY. IF THE SENSOR OPERATES INTERMITTENTLY, THE SES LIGHT MAY ILLUMINATE AND THE VEHICLE MAY RUN ROUGH. THE ENGINE MAY STALL, AND IF SO, MAY RE-START IMMEDIATELY OR AFTER A COOL DOWN PERIOD.

ON CERTAIN PASSENGER VEHICLES, THE NO. 4 LEFT SIDE ENGINE MOUNT BOLT MAY LOOSEN IF A SUDDEN RAPID ACCELERATION IS REPEATEDLY PERFORMED.

ON CERTAIN VEHICLES, IF A SUFFICIENTLY HOT OBJECT ENTERS THE AIR FILTER HOUSING THROUGH THE ENGINE FRESH AIR INTAKE SYSTEM AND CONTACTS THE ENGINE AIR FILTER, THE FLAMMABILITY CHARACTERISTICS OF THE AIR FILTER MATERIAL ARE SUCH THAT THE FILTER MAY IGNITE.

ON CERTAIN PASSENGER VEHICLES, THE FUEL PRESSURE SENSOR LOCATED ON THE LEFT END OF THE FUEL RAIL MAY, AT TIMES, TRANSMIT INCORRECT SIGNAL REGARDING THE FUEL PRESSURE TO THE ENGINE CONTROL MODULE. IF THE SIGNAL IS OUTSIDE OF THE PRE-PROGRAMMED ALLOWABLE LIMITS, A DIAGNOSTIC TROUBLE CODE MAY BE SET AND THE CHECK ENGINE LIGHT WILL COME ON. THE SOLDERED JOINTS ON THE CIRCUIT BOARD OF THE FUEL PRESSURE SENSOR MAY CRACK DUE TO TEMPERATURE CHANGES AND EXCESSIVE VIBRATIONS.

ON CERTAIN MOTORCYCLES, THE CRANKCASE BREATHER SEPARATOR MAY BE DEFECTED. DURING THE MOLDING PROCESS, THE BREATHER PASSAGE MAY HAVE BEEN BLOCKED BY A THIN LAYER OF THE INJECTED PLASTIC MATERIAL. THIS BLOCKAGE WILL CREATE A BUILD-UP OF PRESSURE INSIDE THE CRANKCASE AND MAY CAUSE THE LEFT SIDE ENGINE SEAL TO BE PUSHED OUT OF POSITION AND AN OIL LEAK WILL OCCUR.

ON CERTAIN MOTORCYCLES, FREQUENT SHORT TRIPS PARTICULARLY DURING COLD TEMPERATURES, CAN CAUSE WATER TO ACCUMULATE IN THE OIL TANK, AND WHEN THE ENGINE IS RUNNING, ESCAPING WATER VAPOR CAN CONDENSE ON THE OIL TANK AIR BLEED VALVE. IN FREEZING TEMPERATURES, THIS WATER COULD FREEZE AND BLOCK THE AIR BLEED VALVE.

ON CERTAIN TRUCKS EQUIPPED WITH AN 8.1L V8 (RPO L8-VIN G) ENGINE HAVE A CONDITION IN WHICH THE ENGINE FUEL RAIL PULSE DAMPER RETAINER CLIP MAY FRACTURE RESULTING IN INADEQUATE RETENTION OF THE DAMPER.

ON CERTAIN PASSENGER VEHICLES, DUE TO IMPROPER MOLDING OF THE RESIN BODY OF THE CRANKSHAFT POSITION SENOR INSTALLED ON THE ENGINE BLOCK, ENGINE OIL MAY PENETRATE THE SEAL AND ENTER THE SENSOR WIRING CONNECTOR. THE WIRE HARNESS CONNECTOR MAY NOT BE SUFFICIENTLY ATTACHED TO THE LOCKING TAB OF THE SENSOR WIRING CONNECTOR.

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANK ANGLE SENSOR IS AFFECTED BY TEMPERATURE VARIATIONS. UNDER CERTAIN DRIVING CONDITIONS, THESE VARIATIONS IN TEMPERATURE CAN BE LARGE ENOUGH TO CAUSE A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.

CERTAIN PASSENGER VEHICLES EQUIPPED WITH 2.5L ENGINES MAY EXPERIENCE EXCESSIVE ENGINE OIL CONSUMPTION AS A RESULT OF IMPROPER PERFORMANCE OF THE PISTON RINGS.

CERTAIN REPLACEMENT K&N FUEL PERFORMANCE KITS, P/NOS. 57-1509, 57-1511, 57-1511-1, 57-1517, 57-1517-1, 57-1527, AND 57-1530. ALSO, A SMALL PERCENTAGE OF THESE KITS WERE SOLD UNDER THE MOPAR PERFORMANCE PARTS BRAND NAME (P/NOS. P5007069 AND P5007070). ALL KITS WERE MANUFACTURED FROM APRIL 20, 1999, THROUGH SEPTEMBER 23, 2004. THESE ASSEMBLIES WERE MANUFACTURED AS REPLACEMENT EQUIPMENT FOR CERTAIN DODGE PICKUP TRUCKS AND SUVS. A SMALL PIECE OF MATERIAL FROM THE TUBE WALL COULD BE SUCKED INTO THE ENGINE THROTTLE BODY, WHICH COULD CAUSE THE THROTTLE TO BECOME JAMMED IN THE OPEN POSITION.

IF CERTAIN PASSENGER VEHICLES ARE PARKED AND THE ENGINE IS OPERATED AT HIGH RPM'S FOR AN EXCESSIVE LENGTH OF TIME, SOME OF THE PARTS AROUND THE EXHAUST SYSTEM CAN MELT AND PRODUCE A VARIETY OF MALFUNCTIONS. PROBLEMS CAUSED BY THE EXCESSIVE HEAT BUILD-UP CAN RANGE FROM INOPERATIVE OXYGEN SENSOR, NEUTRAL SWITCH AND BACK UP LIGHTS, PROBLEMS WITH THE PARKING BRAKES, MALFUNCTIONS OF THE GAS GAUGE AND/OR POSSIBLE FUEL LEAKS RESULTING FROM HEAT DAMAGE TO THE FUEL TANK.

ON CERTAIN MOTORCYCLES, EXPOSURE OF THE THROTTLE HOUSING TO ROAD DEBRIS COULD FALL AND BECOME CAUGHT BETWEEN THE THROTTLE-BODY AND THE ENGINE BLOCK.