Wheels Vehicle Recalls

General Motors, LLC (GM) is recalling certain 2026 Chevrolet Silverado EV and GMC Sierra EV vehicles. A manufacturing defect may result in the steel wheels cracking at the disc vent holes.

Chrysler (FCA US, LLC) is recalling certain 2026 Jeep Gladiator and Jeep Wrangler vehicles. The walls for the steel wheels may be too thin, allowing them to crack or detach, which can result in a loss of vehicle control.

Subaru of America, Inc. (Subaru) is recalling certain 2025 Forester vehicles equipped with 18" aluminum alloy wheels. The wheels may have been manufactured with an incorrectly specified lug seat surface, which can result in the wheel being improperly attached and cause a loss of vehicle stability.

Volvo Trucks North America (Volvo Trucks) is recalling certain 2022 VNL vehicles equipped with Alcoa Mirror Polish Wheels, part number ULT 391, and wheel size 22.5 x 8.25. Under certain circumstances, these wheels may not be able to support the load, which can cause the wheels to bend or break while in use.

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2019 Jetta GLI, Golf Alltrack, and Golf GTI vehicles. The front wheel bearings may have been improperly machined, potentially causing excessive stress on the wheel, wheel bolts, or wheel bearings.

Ford Motor Company (Ford) is recalling certain 2018 Ford F53 stripped chassis vehicles equipped with 22.5 inch front wheels. The front wheel hub assembly may have wheel studs that were not properly heat treated.

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018 Toyota Sienna vehicles built with a specific lot of 10-spoke alloy wheels from one production facility. These wheels may not have been properly cooled during manufacturing. As a result, the wheels may crack in the spokes from an impact while driving.

Streetcar ORV LLC, dba American Expedition Vehicles (AEV) is recalling certain 2013-2017 RAM 2500 and 3500 heavy duty trucks, modified by AEV to be equipped with cast aluminum Katla 8.5" road wheels. The outer surface of the wheel may fracture, resulting in rapid air loss.

Kia Motors Corporation (Kia) is recalling certain model year 2014 Cadenza vehicles manufactured February 1, 2013, through August 27, 2013, and equipped with 19" non-chrome aluminum wheels. The wheels on the affected vehicles may fracture from impacts such as large, deep potholes.

BMW of North America, LLC (BMW) is recalling certain model year 2007-2009 F 800 S and F 800 ST motorcycles manufactured August 2006 through January 2009. Due to incorrect tolerances, the rear wheel drive bearing and rear axle may wear.

NISSAN IS RECALLING 3,403 MY 2009 ALTIMA VEHICLES EQUIPPED WITH 16-INCH ALLOY WHEELS. SOME THESE WHEELS MAY NOT HAVE BEEN MANUFACTURED TO SPECIFICATION. THIS COULD CAUSE ONE OR MORE OF THE FIVE LUG NUTS ATTACHING THE WHEEL TO THE VEHICLE TO BECOME LOOSE.

ON CERTAIN VEHICLES EQUIPPED WITH SERIES 0307, HR0307A, HR0307B, HR1000A OR HR1500HB HY--RAIL GUIDE WHEEL EQUIPMENT, THESE STEERING STOPS MAY NOT BE CORRECTLY INSTALLED.

ON CERTAIN POLICE VEHICLES EQUIPPED WITH STEEL WHEELS, SOME OF THE WHEELS MAY DEVELOP CRACKS IN THE RIM NEAR THE WELD LINE THAT CONNECTS THE RIM TO THE DISK.

ON CERTAIN TRUCKS, THE WHEEL SPACER MAY BECOME DISTORTED FROM HEAT WHICH POTENTIALLY COULD LEAD TO A LOSS OF CLAMP THAT MAY RESULT IN LOOSE WHEEL NUTS.

CERTAIN TRUCKS EQUIPPED WITH FRONT STEER AXLE AIR SUSPENSION MAY DEVELOP A FRONT WHEEL WOBBLE WHEN THE TIRES BECOME WORN.

ON CERTAIN MINI VANS EQUIPPED WITH ALLOY WHEELS, MOISTURE CAN ACCUMULATE AROUND THE REAR HUB CAPS CAUSING DAMAGE TO THE OUTER WHEEL BEARING.

ON CERTAIN CAB CHASSIS VEHICLES EQUIPPED WITH ACCURIDE ALUMINUM WHEELS, THE WHEELS WERE NOT PROPERLY PRE-STRESSED. THIS ALLOWS CRACKS TO DEVELOP OVER TIME.

ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH ACCURIDE ALUMINUM WHEELS, THE WHEELS WERE NOT PROPERLY PRE-STRESSED. THIS ALLOWS CRACKS TO DEVELOP OVER TIME.

CERTAIN PASSENGER VEHICLES MAY HAVE A MANUFACTURING FLAW THAT COULD CAUSE THE WHEELS TO CRACK UNDER LONG TERM DRIVING FATIGUE. IF CRACKS OCCUR, WHEEL NOISE AND VIBRATION WILL RESULT AND BECOME PROGRESSIVELY WORSE OVER TIME.

ON CERTAIN SPORT UTILITY VEHICLES, THE FRONT WHEEL SPEED SENSORS MAY BE DEFECTIVE, CAUSING AN ERRONEOUS WHEEL SPEED SIGNAL.

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH FACTORY ALUMINUM ALLOY WHEELS, THE LUG NUT(S) MAY NOT SECURE THE WHEEL PROPERLY TO THE HUB ASSEMBLY DUE TO OVER-DRILLING OF ONE OR MORE OF THE FIVE LUG NUT HOLES ON THE ALLOY WHEEL. IF THE VEHICLE IS DRIVEN FOR AN EXTENDED PERIOD IN THIS CONDITION, THE LUG NUT(S) COULD POTENTIALLY LOOSEN.

2000 NISSAN XTERRA VEHICLES MANUFACTURED BETWEEN OCTOBER 15, 1999, AND FEBRUARY 29, 2000. THE ALLOY WHEELS USED ON THESE VEHICLES MAY NOT HAVE BEEN PROPERLY MANUFACTURED AND COULD DEVELOP CRACKS IN THE WHEEL SPOKES.

ON CERTAIN POLICE AND TAXI VEHICLES EQUIPPED WITH STEEL WHEELS, SOME OF THE WHEELS MAY DEVELOP CRACKS IN THE RIM NEAR THE WELD LINE THAT CONNECTS THE RIM TO THE DISK.

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH 17 INCH CHROME WHEELS, THE CHROME WHEELS WERE NOT HEAT-TREATED. THESE WHEELS MAY CRACK AT THE LUG-NUT HOLES, WHICH COULD RESULT IN THE LOSS OF THE LUG-NUT TORQUE.

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH 17 INCH ALLOY WHEELS, THE WHEELS MAY HAVE A CASTING DEFECT FROM WHICH CRACKS COULD PROPAGATE AS THE VEHICLE IS BEING DRIVEN.

ON CERTAIN SPORT UTILITY VEHICLES EQUIPPED WITH FIVE FACTORY ALLOY WHEELS (MODEL 6934 AND 6936), WITH FACTORY LLAT, AND WITH PORT INSTALLED WR4, FOUR ALLOY WHEEL UPGRADE PROCESSED AT THE JACKSONVILLE, FLORIDA PORT AND DISTRIBUTED BY SOUTHEAST TOYOTA DISTRIBUTORS IN THE STATES OF ALABAMA, FLORIDA, GEORGIA, NORTH AND SOUTH CAROLINA, WHEN THE VEHICLES WERE PROCESSED AT THE PORT, AN ALLOY TIRE/WHEEL UPGRADE WAS INSTALLED. THE UPGRADE INCLUDED 4 ALLOY WHEELS. THE ORIGINAL SPARE TIRE/ALLOY WHEEL WAS NOT CHANGED. THE SPARE TIRE REQUIRES THE USE OF A DIFFERENT STYLE OF WHEEL NUT TO ATTACH IT TO THE VEHICLE.

ON CERTAIN MOTORCYCLES, UNDER CERTAIN RIDING CONDITIONS, SUCH AS CONTINUOUSLY BUMPY ROADS, THE REAR WHEEL COULD DEVELOP STRESS CRACKS WHERE THE WHEEL SPOKES ATTACH TO THE HUB.

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH 6-CYLINDER ENGINES, THE ALUMINUM WHEELS MAY HAVE AN OFF-CENTER DIAMETER.

ON CERTAIN MOTORCYCLES, DUE TO A MANUFACTURING DEFECT, IT IS POSSIBLE THAT THE WHEEL COULD DEVELOP A CRACK. OVER TIME, THE CRACK COULD WORSEN TO THE POINT THAT THE WHEEL FAILED AND THE DRIVE BELT DERAILED.

ON CERTAIN 4X2 VEHICLES EQUIPPED WITH AN ALLOY WHEEL TIRE UPGRADE (OPTIONS WM4, WM8, ZL1-ZL4, DH4, OR DH5) INSTALLED BY THE PROCESSING CENTERS IN JACKSONVILLE, FLORIDA OR COMMERCE, GEORGIA, A LABEL IDENTIFYING THE SPARE TIRE AS A TEMPORARY USE SPARE TIRE WAS NOT INSTALLED. THE UPGRADE INCLUDES 4 LARGER SIZE TIRES WITH ALLOY WHEELS. THE ORIGINAL SPARE TIRE/STEEL WHEEL IS NOT PART OF THE UPGRADE AND WAS NOT CHANGED.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE COOLING HOLES IN THE STEEL WHEEL MAY HAVE BURRS ON THEIR EDGES AS A RESULT OF IMPROPER MANUFACTURING. THESE BURRS CAN CAUSE CRACKS AS THE VEHICLE IS BEING DRIVEN. CRACKS CAN PROPAGATE BETWEEN ADJACENT COOLING HOLES. IF ENOUGH CRACKS DEVELOP BETWEEN THE COOLING HOLES, THE WHEEL COULD FAIL AND SEPARATE FROM THE MOUNTING HUB WITHOUT PRIOR WARNING.